Energy Star's chart and the Department of Energy's flat rule give very different answers for a small room.
As of November 2026, the Energy Star room air conditioner chart assigns 5,000 BTU/h to a room of 100 up to 150 sq ft. The Department of Energy's flat rule of 20 BTU per square foot gives only 2,000 BTU/h at 100 sq ft, so the chart calls for 2.5 times that capacity.
A BTU calculator takes room dimensions, sun exposure and occupancy and returns the heating or cooling capacity, in BTU per hour, that a unit has to deliver. Homeowners use one to choose a window air conditioner, mini split or heater for a single room, and the Energy Star chart is the reference most results get checked against. The flat per-square-foot version undersizes small rooms, which is why the calculator above reads the chart instead.
What Does a BTU Calculator Calculate?
You enter floor area, ceiling height, sun exposure and a few other details, and the tool hands back a single number to match against an air conditioner, heater or furnace.
What one BTU measures
According to the U.S. Energy Information Administration, one British thermal unit is the heat needed to raise one pound of liquid water by 1 degree Fahrenheit. EIA compares a single Btu to the energy released by burning a match.
On an air conditioner box, "BTU" almost always means BTU per hour, which is a rate. Energy Star states room air conditioner capacity in BTUs per hour.
What the result covers
The result is a capacity in BTU per hour. This calculator also shows tons and kW, and a kW value matters mostly for electric heaters.
Running cost isn't part of it, and neither is a model number. A full load calculation for a whole house is a different job entirely. The calculator sizes a room against a rule set, nothing more.
How to use this calculator
- Pick feet or meters, then enter the room length and width. Switch "Measure by" to total floor area for an L-shaped or open-plan room.
- Enter the ceiling height. Above 8 ft the calculator adds a ceiling check next to the chart result.
- Set the sun exposure, the number of people who regularly use the room, and whether the unit cools a kitchen.
- Read the BTU per hour, the tons and kW, and the unit size to buy. Use "Add room" to size several rooms and get a combined total for a multi-zone mini split.
The breakdown under the result shows each step: the chart bracket, the sun percentage, then the fixed amounts for people and a kitchen. The converter under the calculator turns a heater's watts or a furnace's input rating into BTU/h you can compare.
Which Inputs Change the BTU Number?
Floor area sets the base capacity, and the adjustments in the table below move it up or down from there.
| Condition | Adjustment | Type |
|---|---|---|
| Heavily shaded room | Reduce capacity by 10 percent | Percentage |
| Very sunny room | Increase capacity by 10 percent | Percentage |
| More than two regular occupants | Add 600 BTU per extra person | Fixed |
| Kitchen installation | Add 4,000 BTU | Fixed |
Those are the adjustments Energy Star publishes for room air conditioners. The chart has no input for anything else.
Other factors matter too, but the chart doesn't include them. The Citizens Utility Board lists insulation, windows and sun exposure among the things that affect air conditioner size, and its list also takes in nearby heat-generating appliances and the condition of the ductwork. The Department of Energy tells buyers to weigh room height, local climate, shading and window size.
Ceiling height gets a separate mention because the chart doesn't scale with it. Energy Star calculates its capacities for an 8-foot ceiling, and for higher ceilings it only suggests choosing a more capable unit, with no correction factor.
A 10 ft ceiling holds 25 percent more air than an 8 ft one (10 divided by 8). For tall rooms, treat the chart result as a floor and not a final number. The ceiling check in the calculator scales the result by the same ratio, so you can see the top of the range.
How to Calculate BTU for a Room, Step by Step
- Measure the room in feet, converting inches to fractions of a foot. 9 in is 0.75 ft, 6 in is 0.5 ft and 3 in is 0.25 ft.
- Multiply length by width to get the area. A triangular room is length times width divided by two, and anything more complicated gets split into rectangles and triangles whose areas you add up.
- Find that area in the Energy Star chart and read the BTU per hour beside it.
- Apply the percentage adjustment if the room is very sunny or heavily shaded.
- Add the fixed amounts for extra occupants or a kitchen.
Here is how the chart reads at a few sizes, per Energy Star as of November 2026.
- 100 up to 150 sq ft: 5,000 BTU/h
- 250 up to 300 sq ft: 7,000 BTU/h
- 450 up to 550 sq ft: 12,000 BTU/h
- 700 up to 1,000 sq ft: 18,000 BTU/h
The chart starts at 100 sq ft, so a room smaller than that falls outside it. The calculator flags those rooms and points to the smallest 5,000 BTU/h size, and it stops at the chart's top bracket of 2,500 sq ft.
Worked example for a sunny bedroom
The room measures 12 ft 6 in by 14 ft, which is 12.5 x 14 = 175 sq ft. That lands in the 150 up to 250 bracket at 6,000 BTU/h.
Strong afternoon sun adds 10 percent, which brings it to 6,600. Four people use the room regularly, so there are two extras at 600 each. The total comes to 7,800 BTU/h.
Energy Star doesn't state the order of operations. Applying the percentage to the base first and adding the fixed amounts after keeps the occupant allowance from being scaled up with the sun, and that is the order the calculator uses. Pick the "Sunny bedroom" quick start above to see the same 7,800 BTU/h.
Why the flat rule and the chart disagree
The Department of Energy puts the typical requirement at 20 BTU per square foot of living space. Against the chart, that flat rule drifts depending on room size.
At 120 sq ft the chart says 5,000 BTU and the flat rule says 2,400. At 450 sq ft it's 12,000 against 9,000. By 900 sq ft they land on the same 18,000.
So the two methods only agree around 900 sq ft, and below that the flat rule undersizes. The 175 sq ft bedroom above would have come out at 3,500 BTU/h on the rule against 6,000 from the chart.
Converting BTU to Tons and kW
One ton of cooling equals 12,000 BTU per hour. A ton of refrigeration is a rate of heat transfer, not an amount of heat.
The figure comes from melting 2,000 pounds of ice at 32 F in 24 hours, which is 2,000 lb x 144 Btu/lb divided by 24 hours. ACHR News walks through the same arithmetic.
| From | To | Factor |
|---|---|---|
| BTU/h | Tons | Divide by 12,000 |
| BTU/h | kW | Divide by 3,412 |
| kW | BTU/h | Multiply by 3,412 |
| BTU | Joules | Multiply by 1,055 |
EIA's standard electricity factor is 1 kilowatthour = 3,412 Btu. One Btu equals 1,055.05585262 joules.
A kilowatt is a kilowatt-hour per hour, so 1 kW equals 3,412 BTU/h and 1 W equals 3.412 BTU/h. The 7,800 BTU/h bedroom works out to 0.65 tons or about 2.29 kW. A 24,000 BTU/h unit is 2 tons, or about 7.0 kW.
Where the conversion misleads
The kW figure is heat moved, not electricity drawn. Energy efficiency ratio (EER) is cooling capacity in BTU per hour divided by power input in watts.
At an EER of 10 (an illustrative value), a 12,000 BTU/h unit draws 1,200 W, not 3,500 W.
The 12,000 BTU/h ton is also nominal. Manufacturers publish expanded cooling performance tables because the Btu output per ton changes with operating conditions, and it is often not 12,000.
How the Calculation Changes for Heating
Heating follows heat loss to the outdoors, so the same room needs a different number in winter than it does in summer.
Carrier states that climate plays a major role in system sizing. It also says a proper furnace calculation counts the home's actual heat loss and not just its square footage.
The inputs include climate zone and the gap between the outdoor design temperature and the indoor target, plus insulation and window quality. Ductwork counts when the heat travels through ducts, and so does the layout of the home.
Furnaces add a labeling trap. Energy Vanguard points out that the figure that matters is output capacity, meaning how quickly BTUs reach the house, and not the rate of fuel input. AFUE is the share of fuel energy a furnace converts into usable heat, which links the two ratings.
A 100,000 BTU/h furnace at 80% AFUE delivers 80,000 BTU/h, and the same input at 96% AFUE delivers 96,000 BTU/h. Compare furnaces on output, and check whether the label states input or output before you read it against your result. The furnace box in the converter does this multiplication for you.
Electric space heaters are simple. A 1,500 W unit turns all of its power into heat, so 1,500 x 3.412 gives 5,118 BTU/h.
Heat pumps don't work that way, because their heating output depends on outdoor temperature. That is why the Northwest Energy Efficiency Alliance (NEEA) screens cold-climate ductless models by how much capacity they keep at 5 F, and it recommends units that retain at least 80 percent of their rated 47 F capacity at that temperature.
Matching the Result to a Window AC, Mini Split, Furnace or Central System
| Equipment | How the BTU result applies | Rating to watch |
|---|---|---|
| Window AC | Match the room result directly | Rated cooling capacity |
| Portable AC | Match against the SACC figure | SACC, not ASHRAE |
| Ductless mini split | Size each zone on its own | Cooling and heating capacity |
| Central AC or heat pump | Whole-house load, stated in tons | Capacity at design conditions |
| Furnace | Heating load, not floor area | Output BTU/h |
Portable units carry two ratings, and only one of them tells you what the unit does in a room.
The Department of Energy's 2016 test procedure for portable air conditioners includes seasonally adjusted cooling capacity (SACC). Honeywell describes it as a weighted average of performance across temperatures and humidity levels. TCL's support documentation states that the SACC figure is lower than the older ASHRAE figure, so size a portable unit against SACC.
Mini splits are messier. Manufacturers publish coverage charts, and those charts do not match the room air conditioner chart.
Trane's chart lists a 9,000 BTU mini split for 240 to 360 sq ft. Energy Star's room AC chart gives 9,000 BTU for 350 up to 400 sq ft. The two part ways at the large end, where Trane assigns 24,000 BTU to 720 to 960 sq ft and Energy Star puts 24,000 BTU at 1,400 up to 1,500 sq ft.
Trane states that its chart uses a multiplier of 25 BTU per square foot, which is why its larger sizes cover far less floor area. Its chart also covers mini splits that heat and cool, while Energy Star's covers cooling in a single room, so treat them as separate scopes. Trane also warns that an undersized mini split runs continuously and may not heat or cool the space adequately.
What Happens When the BTU Number Is Wrong?
An oversized unit short-cycles and leaves the room damp. A unit that's too small just runs without pause and misses the setpoint.
Energy Star states that an oversized air conditioner cools the room before it removes the humidity. For conventional room units, it also describes the compressor alternating between full on and off. Energy Vanguard notes that a short runtime cannot remove moisture, because the unit shuts off first, and Trane says the stress of too many starts and stops shortens equipment life and raises bills.
On the undersized side, a Penn State course module on air conditioner sizing says the unit runs continuously but cannot hold the setpoint at peak heat. Run time and electricity use climb while comfort does not.
The undersizing penalty is smaller than most guides imply. Green Building Advisor's Manual S sizing calculator accepts a total cooling capacity as low as 90 percent of the load in some cases, so a slightly small unit can still be within the standard. Contracting Business gives the usual air conditioner range as 100 to 115 percent of the total cooling load.
Oversizing is worse partly because peak conditions are rare. Summer design temperature is exceeded about 87.6 of the 8,760 hours in a year, according to Green Building Advisor, so a unit sized to that peak runs well below capacity for the rest of the year.
Capacity is not efficiency
A BTU result tells you the capacity you need and nothing about what that capacity costs to run. Efficiency ratings cover the cost side.
SEER2 covers seasonal cooling efficiency, and EER2 covers cooling efficiency at a fixed test condition. Heat pumps also get HSPF2, for seasonal heating.
The "2" metrics took effect on January 1, 2023, when DOE's Appendix M1 test procedure replaced Appendix M for single-phase equipment below 65,000 BTU/h (Gemaire; AHRI).
NY Engineers notes that the new procedure is more demanding, so SEER2 values come out lower than the old SEER values for the same equipment. A higher rating never substitutes for a correct BTU number.
BTU Calculator vs. Manual J for Sizing a System
For a single room, or a window, portable or mini split unit, a BTU calculator does the job. Central systems, whole houses and equipment replacements call for an ACCA Manual J load calculation.
When Manual J is the right tool
Contracting Business describes Manual J, 8th Edition, as ANSI-accredited and written into the International Code Council codebooks as the baseline for calculating loads. ACCA adds that national building codes and most state and local jurisdictions require it. ServiceMag notes that a full calculation produces a load for every room, not just one for the house.
Manual J gives a load, not a unit size. Green Building Advisor stresses that the Manual S protocol takes the next step and selects the equipment.
Green Building Advisor puts the common rule of thumb at 400 to 600 sq ft per ton, with 500 the usual midpoint. The measured numbers look quite different. An average of 40 Manual J calculations in hot climates came to 1,431 sq ft per ton. A separate batch of equipment sizing jobs, 151 systems across 63 homes, averaged 856 sq ft per ton. The same source says Manual J loads run 10 to 20 percent above actual cooling loads.
Run those ratios on a 3,000 sq ft house. The 500 sq ft rule gives 6 tons. The 856 average gives about 3.5 tons, and the 1,431 load average gives about 2.1 tons.
The rule of thumb overshoots even the equipment sizes that follow a proper Manual S selection, by roughly 70 percent in this example.
Sources describe one Manual S figure differently. ACHR News calls 115 percent of the cooling load the lowest excess capacity Manual S specifies, while Contracting Business and Slashgear treat 115 percent as the ceiling, meaning an air conditioner may not exceed it. The ceiling reading matches Contracting Business's worked example, where a 30,000 BTU/h load allows at most 34,500 BTU/h, and it matches the International Energy Conservation Code, which caps cooling-only equipment at 1.15 times the design cooling load.
The ceiling also depends on equipment type. Contracting Business gives 115 percent of the total cooling load for air conditioners and 140 percent of the heating load for furnaces, so check the Manual S limit for the specific equipment being selected.
When the calculator result stops being reliable
Whole houses and central systems are the first case, since duct losses and room-by-room loads decide the answer there. Replacements are another weak spot, because the old unit's size is no evidence of the right size.
Homes whose insulation, windows or layout differ sharply from the chart's assumptions fall outside it too. So does any situation where the result would be used to pick a tonnage and not a window unit.
Green Building Advisor's underlying point about square-foot rules is that they ignore the features of a house that drive cooling and simply scale the system to its size.
Choosing a Size When the Result Falls Between Two Units
When a result lands between two unit sizes, go with the closest capacity, and step down rather than up if the room is shaded.
Take the 7,800 BTU/h bedroom result. A 7,000 BTU/h unit covers about 90 percent of that load, while an 8,000 BTU/h unit covers 103 percent.
The room is very sunny, so the larger unit wins. The smaller one would leave a shortfall of about 10 percent on the hottest afternoons.
Before buying, check the rating basis on the label (SACC for portable units, output for furnaces). After that, look at the share of the load each candidate covers, and last, the humidity cost of the larger option. The "Unit size to buy" panel in the calculator shows both neighboring sizes with the share of the load each one covers.
The larger unit trades some humidity control on mild days for headroom on peak days. This sequence rests on the Energy Star chart as verified in November 2026, and a revised chart would shift the size brackets.
BTU Calculator FAQ
How many BTU does a garage, basement or sunroom need?
Start from floor area in the Energy Star chart, then adjust for conditions. Energy Star calls for a 10 percent increase in a very sunny room and a 10 percent reduction in a heavily shaded one.
A glass-heavy sunroom takes the sun increase. An uninsulated garage needs a load calculation instead, because the chart has no insulation input.
Can one mini split cool several rooms?
Not well. One indoor head serves one zone, so a single unit does not cool separate rooms. Multi-zone systems connect several indoor heads to one outdoor unit.
Size each head to its own room, then check that the outdoor unit covers the combined load.
How many BTU does a radiator need?
Size it against the heat the room loses, the same logic as any heating load. Radiator output appears in watts or BTU/h, and 1 W equals 3.412 BTU/h.
Several radiators can be combined, or a single one used, to reach the BTU requirement.
Can two small units replace one large air conditioner?
Yes. BTU per hour is a rate, so two 6,000 BTU/h units deliver 12,000 BTU/h together.
Keep the combined total close to the calculated figure, and place each unit so its airflow reaches the room.